Gear Locker with Security Box and Drawer

The Right Locker for the Right Job

Our gear locker with security box and drawer adds a new twist to the standard locker by introducing a series of storage drawers that fit inside the locker. This design frees up valuable floor space in front of the locker when the drawer is not in use and features vertical dividers that permit you to create compartments or just use the drawer to stow bulky items like shoes or patrol bags. The drawer system features an integral full-width pull and heavy duty ball-bearing glides. To save room in tight quarters, combine the drawers with an available seat to open up the area in front of the lockers. The range of locker widths and accessories for gear lockers makes planning lockers for any line of security or emergency service easy. The featured locker has a 24” wide security compartment that has room for everything from toiletries to pepper spray, and with its full shelf you can still stow a citation book, binder, clipboard and file folders. An available clothing separator spaces uniforms, jackets and ballistic vests for better air circulation. Two different sizes of storage compartments, available drawers, heavy duty hooks and a sheet metal document pocket can be added to organize your gear for the next patrol.

This unit includes (as pictured)

1. Top Shelf
2. Drawer Unit
3. 2 half shelves
4. Coat Rod
5. Doors
6. Mirror
7. Cell Phone Tray
8. 2 drawer dividers

Key Features:

• Heavy Duty Lockers:  All locker body components made of cold rolled steel specially formed for added strength and rigidity and to ensure tight joints at fastening points
• Locker Body:  Sides, bottoms, tops, and shelves: 16-gauge steel. Sides punched for shelf locations on nominal 12" centers
• Backs:  Solid 18-gauge steel
• Sides:  16-gauge sheet steel with 3/4" (19mm) wide by 1-1/2" (38mm) high diamond-shaped perforations. Optional: solid sides without ventilation
• Tops and Bottoms:  Three sides formed 90 degrees, the front offset formed to be flush with horizontal frame member
• Frame:  Vertical frame member to be not less than 16-gauge formed to a channel shape and hemmed to create a smooth interior edge. Intermembering parts to be mortised and tenoned and electrically welded together in a rigid assembly capable of resisting strains. Hole spacing in locker body construction does not exceed 9" (225 mm)
• Assembly Hardware:  Zinc plated truss fin head bolts and hex nuts; optional factory assembly of locker bodies using rivets
• Interior Equipment Shelf:  16-gauge full width located approximately 12" (304.8 mm) below top of locker
• Hooks and Coat Rod:  Two heavy duty 3" high x 7/8" wide x 2-1/2" deep single-prong wall hooks and one chrome plated 1" diameter coat rod
• Powder Coat:  Dry Thickness: 1 to 1.2 mils (0.025 to 0.03 mm)
• Color:  21 color choices; call for two-tone color options
• Door Handles and Cremone Latching:  Heavy duty turn handle secures the door at three points. The top and bottom frames are engaged with 3/8" (9.5 mm) steel rods, and a 1/8" (3 mm) thick center latch engages at the side. Double doors have a left hinged door secured its full length by the right hinged door when latched. Handle is secured to door using a threaded lock nut to facilitate adjustment and removal for repair if necessary. Welded handle assemblies are not accepted
• Single Point Latch:  24” wide single door only. Recessed handle with integral pull and 11-gauge steel hasp welded to locker frame
• Multiple Point Latch:  24” wide single door only. Recess finger-lift control handle in door, positive automatic type latching, whereby locker may be locked when open, then closed without unlocking

Custom Features: Available upon request. Call 1-877-952-0151 or E-mail us.

Document Sleeve	Cell Phone/Key Tray	Accessory Mounting Panel	Garment Separator

• Cell Phone/Key Tray:  The 8” x 2” x 2” tray is sized for organizing phones, radios or keys and can be attached to the optional center divider or to the door using the accessory mounting panel
• Hardwood Seat:  Used in place of a foot locker or drawers, the 1-1/4” thick full hardwood bench provides a sturdy seating surface with open storage underneath for stowing equipment
• Foot Locker:  The reinforced lid of the foot locker features a continuous hinge and also serves as a seat. The front panel includes a single point latch with padlock strike plate and mini louvers for security and ventilation
• Document Sleeve:  Formed from 16-gauge steel, the document sleeve is available in either a vertical or horizontal configuration for efficient storage of portfolios, note pads or binders
• Garment Separator:  The 16-gauge steel channel attaches underneath the top shelf and uses diamond perforations to keep hangers from bunching together for improved ventilation
• Drawer Unit:  Mounted within the confines of the locker body, the steel drawer features full extension glides for easy access to files or equipment without taking up valuable space when not in use. The ball-bearing glides are rated at 250 lb. capacity for performance and durability
• Parachute Rack:  Formed from 3/4" diameter, heavy wall steel tube and reinforced by 14-gauge gussets and supports for hanging heavy flight gear or body armor. Ordering this option replaces the standard heavy duty rear-mounted coat hooks
• Boot Tray:  The 12” x 14” boot tray provides air space between soiled or wet footwear and the shelf or locker bottom. A series of round perforations are used promote air flow and the tray is kept from marring the locker finish by rubber pads
• Accessory Mounting Panel:  A 24" high panel formed from 16-gauge steel permits mounting several accessories to the door without drilling or using exposed fasteners
• Additional Locker Accessories:  Standard locker accessories such as vertical fillers, continuous slope hoods, locker room benches and recess trim are available for use on gear lockers
• Security Box:  Available in either 15” or 24” wide configurations, the security box uses a 14-gauge lockable door, 16-gauge side panel and welded door frame to properly secure valuable equipment and personal items. The 24” model includes a full width shelf to double the usable storage area. Any standard box locker padlock or built-in lock can be used to secure the contents
• Coat Rod:  Chrome plated 1" diameter coat rod.
• Hooks:  Heavy duty coat hooks ensure exceptional hanging capacity below
• Center Divider:  Center divider allows you to split your storage between uniforms or PPE and civilian clothing storage for more flexibility
• Half Shelves:  Combine several half shelves with a divider and locking compartment
• Shelves:  Sturdy full width shelf located 12” below the top to provide ample storage for protective head gear. Flanged on four sides formed to 90 degrees, front edge having a second bend

Color Chart